- 您現在的位置：買賣IC網 > Datasheet目錄1 > 19-137/R6GHBHC-A01/2T (Everlight Electronics Co Ltd)LED RED/GREEN/BLU WATER CLR 0603 Datasheet資料下載
參數資料
| 型號： | 19-137/R6GHBHC-A01/2T |
| 廠商： | Everlight Electronics Co Ltd |
| 文件頁數： | 12/13頁 |
| 文件大?。?/td> | 259K |
| 描述： | LED RED/GREEN/BLU WATER CLR 0603 |
| 標準包裝： | 3,000 |
| 顏色： | 紅，綠，藍（RGB） |
| Millicandela 等級： | 100mcd 紅，180mcd 綠，50mcd 藍 |
| 正向電壓： | 2V 紅，3.3V 綠，3.3V 藍 |
| 電流 - 測試： | 20mA |
| 波長 - 主： | 624nm，525nm，470nm |
| 波長 - 峰值： | 632nm，518nm，468nm |
| 視角： | 120° |
| 透鏡類型： | 透明 |
| 透鏡樣式/尺寸： | 矩形，帶平頂，1.6mm x 0.8mm |
| 封裝/外殼： | 4-SMD，無引線 |
| 尺寸/尺寸： | 1.60mm L x 1.60mm W |
| 高度： | 0.50mm |
| 安裝類型： | 表面貼裝 |
| 包裝： | 帶卷 (TR) |
第1頁第2頁第3頁第4頁第5頁第6頁第7頁第8頁第9頁第10頁第11頁當前第12頁第13頁
DATASHEET
SMD B
19-137/R6GHBHC-A01/2T
12
Copyright ?2010, Everlight All Rights Reserved. Release Date : 28-Jun-2013. Issue No: DSE-0002500 Rev.5
www.everlight.com
Precautions For Use
1. Over-current-proof
Customer must apply resistors for protection, otherwise slight voltage shift will cause big
current change ( Burn out will happen ).
2. Storage
2.1 Do not open moisture proof bag before the products are ready to use.
2.2 Before opening the package: The LEDs should be kept at 30 or less and 90%RH or less.
2.3 After opening the package: The LED's floor life is 1 year under 30 or less and 60% RH or less.
If unused LEDs remain, it should be stored in moisture proof packages.
2.4 If the moisture absorbent material (silica gel) has faded away or the LEDs have exceeded the
storage time, baking treatment should be performed using the following conditions.
Baking treatment : 60? for 24 hours.
3. Soldering Condition
3.1 Pb-free solder temperature profile
Pre-heating
150~200癈
60~120sec.
Above 217癈
60~150sec.
260癈 M ax.
10sec. Max.
6癈/sec.M ax.
Above255癈
30sec.M ax.
3癈/sec.Max.
3.2 Reflow soldering should not be done more than two times.
3.3 When soldering, do not put stress on the LEDs during heating.
3.4 After soldering, do not warp the circuit board.
4.Soldering Iron
Each terminal is to go to the tip of soldering iron temperature less than 350 for 3 seconds within once in less than the
soldering iron capacity 25W. Leave two seconds and more intervals, and do soldering of each terminal. Be careful because
the damage of the product is often started at the time of the hand solder.
5.Repairing
Repair should not be done after the LEDs have been soldered. When repairing is unavoidable, a double-head soldering
iron should be used (as below figure). It should be confirmed beforehand whether the characteristics of the LEDs will or will
not be damaged by repairing.
相關PDF資料 |
PDF描述 |
|---|---|
| 204-10SURC/S530-A3 | LED 3MM HYPER RED WATER CLEAR |
| 204-10SURD/S530-A3 | LED 3MM BRILLIANT RED RED DIFF |
| 204-10SURT/S530-A3 | LED 3MM HYPER RED RED TRANSFL |
| 204-10SYGT/S530-E2 | LED 3MM SUPER YLW-GRN GRN TRANSF |
| 204-10USOC/S400-A9 | LED 3MM SUPER SUNSET ORANGE CLR |
相關代理商/技術參數 |
參數描述 |
|---|---|
| 1913800000 | 制造商:Weidmuller 功能描述: |
| 1913810000 | 制造商:Weidmuller 功能描述: |
| 1913820000 | 制造商:Weidmuller 功能描述:LMZF 5/3/135 3.5OR |
| 1913830000 | 制造商:Weidmuller 功能描述: |
| 1913840000 | 制造商:Weidmuller 功能描述: |
發布緊急采購，3分鐘左右您將得到回復。